Specialized Industries
Resco Products has been supplying refractories to North America and the world for over 70 years. Our industry and product experts are able to apply years of hands-on experience to evaluate your refractory needs. Since we are a full line supplier, we offer a large number of monolithic and brick, and when required, we can offer new products to meet your specific needs by working closely with our R&D group to design a new product.
Coke Calcining Refractory
The coke calcining process is dependent on the duration and temperature the petroleum green coke endures while traveling through the rotary kiln. To achieve optimal properties of density and conductivity, the coke must stay at a temperature of 1150-1350°C (or higher). Resco Products has the supplies to achieve optimal levels of efficiency to generate high quality refractory products for the coke calcining industry.
Rotary Hearth Furnace Refractory
Resco Products has created a variety of schematics and products variations to fit all different sizes of rotary hearth furnaces. Resco provides the high-quality rotary hearth furnace refractory supplies as well as a more fully customizable solution for each process. Our trained specialists operate with your best interest in mind keeping your energy efficient while producing lower CO2 emissions than a blast furnace.
RELATED PRODUCTS
Caulk
22 Caulk
22 Caulk
22 CAULK is ideal for filling joints and cracks in refractory linings. Job site mixing is not needed. Just snip-off the tip of the ready-to-use caulking tube and apply the moist material using a hand or air powered caulking gun. Heat loss through joints and cracks will be reduced. Fine particles will not accumulate in those openings, preventing further damage to the lining. The surface of 22 CAULK will harden when exposed to air.
22 CAULK is ideal for filling joints and cracks in refractory linings. Job site mixing is not needed. Just snip-off the tip of the ready-to-use caulking tube and apply the moist material using a hand or air powered caulking gun. Heat loss through joints and cracks will be reduced. Fine particles will not accumulate in those openings, preventing further damage to the lining. The surface of 22 CAULK will harden when exposed to air.
Caulk
22 Caulk (UK)
22 Caulk (UK)
22 CAULK is ideal for filling joints and cracks in refractory linings. Job site mixing is not needed. Just snip-off the tip of the ready-to-use caulking tube and apply the moist material using a hand or air powered caulking gun. Heat loss through joints and cracks will be reduced. Fine particles will not accumulate in those openings, preventing further damage to the lining. The surface of 22 CAULK will harden when exposed to air.
22 CAULK is ideal for filling joints and cracks in refractory linings. Job site mixing is not needed. Just snip-off the tip of the ready-to-use caulking tube and apply the moist material using a hand or air powered caulking gun. Heat loss through joints and cracks will be reduced. Fine particles will not accumulate in those openings, preventing further damage to the lining. The surface of 22 CAULK will harden when exposed to air.
Wet Mortar
Adacor 70 Dip
Adacor 70 Dip
ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Wet Mortar
Adacor 70 TR-D3.5
Adacor 70 TR-D3.5
ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 70 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 70 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Wet Mortar
Adacor 80 Dip
Adacor 80 Dip
ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Wet Mortar
Adacor 80 TR-D3.5
Adacor 80 TR-D3.5
ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
ADACOR 80 is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. ADACOR 80 is recommended for laying up super duty, high alumina, and mullite brick. It has a high alumina content which gives the product resistance to erosion and also a high bonding strength at temperatures up to 3200°F.
Dry Mortar
Adamant Air Set-Dry
Adamant Air Set-Dry
A dry, air-setting fireclay - silica based mortar, with a maximum service temperature of 3000°F, used for bonding super duty brick. Just add water to obtain the desired trowel or dipping consistency. This product will take an air set, but does not develop its full joint strength until after heating to 220°F (105°C)
A dry, air-setting fireclay - silica based mortar, with a maximum service temperature of 3000°F, used for bonding super duty brick. Just add water to obtain the desired trowel or dipping consistency. This product will take an air set, but does not develop its full joint strength until after heating to 220°F (105°C)
Wet Mortar
Adamant X Green
Adamant X Green
ADAMANT X is a fireclay-silica based material with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time. ADAMANT X is the original wet air setting cement for bonding intermediate, high heat and super duty fireclay brick. Produced since 1907, ADAMANT X was one of the first bonding mortars introduced to industry that truly bonded brick together. Through the years, the ADAMANT X trademark has stood for quality and has been widely accepted by refractory consumers.
ADAMANT X is a fireclay-silica based material with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time. ADAMANT X is the original wet air setting cement for bonding intermediate, high heat and super duty fireclay brick. Produced since 1907, ADAMANT X was one of the first bonding mortars introduced to industry that truly bonded brick together. Through the years, the ADAMANT X trademark has stood for quality and has been widely accepted by refractory consumers.
Wet Mortar
Adamant X Yellow
Adamant X Yellow
ADAMANT X is a fireclay-silica based material with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time. ADAMANT X is the original wet air setting cement for bonding intermediate, high heat and super duty fireclay brick. Produced since 1907, ADAMANT X was one of the first bonding mortars introduced to industry that truly bonded brick together. Through the years, the ADAMANT X trademark has stood for quality and has been widely accepted by refractory consumers.
ADAMANT X is a fireclay-silica based material with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time. ADAMANT X is the original wet air setting cement for bonding intermediate, high heat and super duty fireclay brick. Produced since 1907, ADAMANT X was one of the first bonding mortars introduced to industry that truly bonded brick together. Through the years, the ADAMANT X trademark has stood for quality and has been widely accepted by refractory consumers.
Wet Mortar
Adaphos 85 Dip
Adaphos 85 Dip
ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
Wet Mortar
Adaphos 85 TR-D3
Adaphos 85 TR-D3
ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
ADAPHOS 85 is a wet ready-mixed high alumina bonding mortar with a chemical bonding system. With the unique bonding system, a high bonding strength is developed at lower temperatures (300-600°F) and the high bonding strength continues until a ceramic bonding occurs. ADAPHOS 85 is primarily used to lay up high alumina brick in ladles and is available in both trowelling and dipping consistencies. It is used in areas where severe service conditions require increased refractoriness to corrosion/erosion from slags.
Alumina Brick
Alumex P-85-HS
Alumex P-85-HS
ALUMEX® P-85 HS exhibits a combination of very high strengths, high abrasion resistance, and excellent thermal shock resistance. Its high purity composition yields a refractory product that can withstand severe alkali attack.
Dry Mortar
Alutab
Alutab
ALUTAB® is a high purity, 85% alumina mortar compatible with 70%, 80%, and 90% alumina brick. It is designed for use under the most severe conditions where high refractoriness, good bond strength, and resistance to attack by molten metal and slag are the prime requirements. It is air-setting with a 3400°F service temperature limit.
ALUTAB® is a high purity, 85% alumina mortar compatible with 70%, 80%, and 90% alumina brick. It is designed for use under the most severe conditions where high refractoriness, good bond strength, and resistance to attack by molten metal and slag are the prime requirements. It is air-setting with a 3400°F service temperature limit.
Coatings
A-O Brush Mix
A-O Brush Mix
A-O BRUSH MIX is an oxidation protective coating for carbon containing refractory shapes. A-O BRUSH MIX is especially designed to coat MgO-C slagline brick of ladles by brushing or spraying to protect from carbon oxidation during the preheating period by forming high viscosity frits. It begins to soften at approximately 750oF and frits at 1100oF when formation of a dense layer seals the brick surface and joints to stop the penetration of oxygen. The molten A-O BRUSH MIX is very reactive. It reacts at high temperatures with viscosity increasing agents being part of the product, as well as with the MgO of bricks. Due to this property, A-O BRUSH MIX forms a protective layer even at 2500oF without flowing off.
A-O BRUSH MIX is an oxidation protective coating for carbon containing refractory shapes. A-O BRUSH MIX is especially designed to coat MgO-C slagline brick of ladles by brushing or spraying to protect from carbon oxidation during the preheating period by forming high viscosity frits. It begins to soften at approximately 750oF and frits at 1100oF when formation of a dense layer seals the brick surface and joints to stop the penetration of oxygen. The molten A-O BRUSH MIX is very reactive. It reacts at high temperatures with viscosity increasing agents being part of the product, as well as with the MgO of bricks. Due to this property, A-O BRUSH MIX forms a protective layer even at 2500oF without flowing off.
Coatings
Blox Stix
Blox Stix
BLOX STIX is a fibrous adhesive used to adhere block insulation to steel or other substrates. BLOX STIX aids the installation of mineral fiber, calcium, silicate and vermiculite based block insulation.
Pressed Shape
C-4
C-4
Highly refractory material used in the continuous casting process for making metal railroad wheels. It is non-wetting for ferrous metals.
Kiln Furnitures
Cordierite Mix 05-05
Cordierite Mix 05-05
A high strength, thermal shock resistant, pressed cordierite mix suited for kiln furniture requirements
Plastic
Corline
Corline
CORLINE® was designed for linings exposed to extreme erosion environments in heat enclosures of the oil refining, petrochemical, gas processing and solid fuels processing industries. CORLINE® is a High Alumina, Chemically Bonded, Erosion Resistant Refractory.
RAM
Corpatch 50 MS
Corpatch 50 MS
CORPATCH® 50-MS is an 50% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
RAM
Corpatch 80
Corpatch 80
CORPATCH® 80 is an 80% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
RAM
Corpatch 80 MS
Corpatch 80 MS
CORPATCH® 80-MS is an 80% alumina patching mix. It is an all purpose patching mix that is tough enough to be one of the best erosion or abrasion resistant refractory lining materials available today, yet it is pliable enough to be installed and shaped by hand or mallet.
Wet Mortar
Door Seal
Door Seal
DOOR SEAL is an silicate-based, liquid sealant that expands, when applied, to seal coke oven door sealing surfaces and virtually eliminates door emissions.
Alumina Brick
DuraLite 70 G
DuraLite 70 G
Burned High Alumina Brick
Alumina Brick
DuraLite 80 G
DuraLite 80 G
High Alumina Brick
Alumina Brick
DuraLite 85 G
DuraLite 85 G
High Alumina Brick
Conventional Castable
EZ Cast 2700
EZ Cast 2700
EZ CAST® 2700 is a general purpose, economical castable designed for applications up to 2700°F. Its high strength and ability to be pumped or poured make it the ideal choice for any number of applications where access is limited or obstructions make work difficult. It is particularly effective in applications where destructive gases and atmospheres or excessive wear shorten refractory life.
EZ CAST® 2700 is a general purpose, economical castable designed for applications up to 2700°F. Its high strength and ability to be pumped or poured make it the ideal choice for any number of applications where access is limited or obstructions make work difficult. It is particularly effective in applications where destructive gases and atmospheres or excessive wear shorten refractory life.
Conventional Castable
EZ Cast 2800
EZ Cast 2800
EZ CAST® 2800 is similar to EZ CAST® 2700, except designed for applications up to 2800°F. In the laboratory, this product has tested well for resistance to CO (carbon monoxide) disintegration encountered in coke ovens and blast furnaces.
Conventional Castable
EZ Cast 2800 Fine
EZ Cast 2800 Fine
EZ CAST® 2800 FINE is a Fine-Grained, Conventional Cement, 45% Alumina castable that can be installed by vibration cast, pumpcasting, or self-leveling methods.
Low Cement Castable
EZ Cast 3000
EZ Cast 3000
EZ CAST® 3000 is a self-flowing, low iron, 56% alumina, low cement castable designed to provide high strength and good thermal shock and abrasion resistance. It offers good slag resistance for severe applications up to 3000°F. In the laboratory, this product has shown excellent resistance to CO atmospheres found in coke ovens and blast furnaces. Large volumes of this castable have been used successfully in a wide variety of applications.
EZ CAST® 3000 is a self-flowing, low iron, 56% alumina, low cement castable designed to provide high strength and good thermal shock and abrasion resistance. It offers good slag resistance for severe applications up to 3000°F. In the laboratory, this product has shown excellent resistance to CO atmospheres found in coke ovens and blast furnaces. Large volumes of this castable have been used successfully in a wide variety of applications.
Low Cement Castable
EZ Cast 3200
EZ Cast 3200
EZ CAST® 3200 is a self-flowing, 76% alumina low cement castable designed to provide longer service life and superior performance in steel applications with temperatures up to 3200°F. It also has outstanding strength and abrasion resistance. In laboratory testing this product has shown excellent resistance to CO atmospheres found in coke ovens and blast furnaces.
EZ CAST® 3200 is a self-flowing, 76% alumina low cement castable designed to provide longer service life and superior performance in steel applications with temperatures up to 3200°F. It also has outstanding strength and abrasion resistance. In laboratory testing this product has shown excellent resistance to CO atmospheres found in coke ovens and blast furnaces.
Low Cement Castable
EZ Cast 3250
EZ Cast 3250
EZ CAST® 3250 is a low cement castable with an alumina content of 78%. It has excellent abrasion resistance and superior hot strength to as high as 2700°F. These properties combined with excellent thermal shock resistance have resulted in many successful installations in bottoms and lip rings of steel ladles. This proven product has been successfully used in a wide variety of applications, often substituted for higher alumina content products, making it a highly cost-effective and versatile composition. Its combination of strength, toughness, alumina content, and other compositional features make it an excellent product for many applications.
EZ CAST® 3250 is a low cement castable with an alumina content of 78%. It has excellent abrasion resistance and superior hot strength to as high as 2700°F. These properties combined with excellent thermal shock resistance have resulted in many successful installations in bottoms and lip rings of steel ladles. This proven product has been successfully used in a wide variety of applications, often substituted for higher alumina content products, making it a highly cost-effective and versatile composition. Its combination of strength, toughness, alumina content, and other compositional features make it an excellent product for many applications.
Conventional Castable
EZ Cubed 2700
EZ Cubed 2700
EZ CUBED® 2700 is a conventional cement-bonded, fireclay-based, 42% Alumina castable that can be installed by vibration cast , pumpcasting, self-leveling, or shotcreting methods.
Conventional Castable
EZ Cubed 2800
EZ Cubed 2800
EZ CUBED® 2800 is a cement-bonded, fireclay-based, 45% Alumina castable that can be installed by vibration cast , pumpcasting, self-leveling, or shotcreting methods.
Low Cement Castable
EZ Cubed 3000
EZ Cubed 3000
EZ CUBED® 3000 is a Low Cement, 55% Alumina castable that can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
Low Cement Castable
EZ Cubed 3200 Fine
EZ Cubed 3200 Fine
A low cement, 75% alumina castable with a maximum service temperature of 3200°F. This castable can be used in a wide variety of refractory applications. The product can be installed by vibration casting, pumping, and shotcreting methods.
Low Cement Castable
EZ Cubed 35-30
EZ Cubed 35-30
Self flow/pumpable /low cement/SiC containing thermal shock and corrosion resistant castable
Low Cement Castable
EZ Cubed 60 LQY
EZ Cubed 60 LQY
An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack.
Low Cement Castable
EZ Cubed 60M
EZ Cubed 60M
Mullite-based/ self flow/pumpable/shotcrete/low cement castable
Low Cement Castable
EZ Cubed 60M XT
EZ Cubed 60M XT
Mullite-based/ self flow/pumpable/shotcrete/low cement castable
Low Cement Castable
EZ Cubed 70PC
EZ Cubed 70PC
EZ CUBED® 70PC is a Low Cement, 70% Alumina castable that can be installed by vibration cast, pumping or shotcreting methods.
Low Cement Castable
EZ Cubed 80-15
EZ Cubed 80-15
EZ CUBED® 80-15 is a Low Cement, 80% Alumina castable containing a silicon carbide addition that can be installed by vibration cast, self-flowing, pumping or shotcreting methods.
Conventional Castable
EZ Cubed Lo-Erode
EZ Cubed Lo-Erode
EZ CUBED® LO-ERODE® can be vibration cast or poured in addition to shotcreted and can be used at temperatures up to 2600°F. It is a shotcrete mix that will meet the tough property standards at 1500°F required by the hydrocarbon processing industry.
Chemically Bonded Castables
EZ EST 10CR
EZ EST 10CR
EZ EST 10CR is a cement-free, alumina-chrome castable with 10% chromic oxide, that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation.
Chemically Bonded Castables
EZ EST 20CR
EZ EST 20CR
EZ EST 20CR is a cement-free, alumina-chrome castable with 20% chromic oxide, that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation.
Chemically Bonded Castables
EZ EST 32-70 PC
EZ EST 32-70 PC
EZ EST 32-70 PC is a colloidal-silica bonded, pumpable castable. This product is engineered for short turnaround after placement. The colloidal silica binder must be added as a separate component.
Chemically Bonded Castables
EZ EST 60PC
EZ EST 60PC
EZ EST 60PC is a cement-free, 60% alumina castable that can be installed by casting, pumping, or shotcreting methods. This product requires an additional liquid binder, called EZ ADD binder, for mixing and installation
Chemically Bonded Castables
EZ EST 60Z PC
EZ EST 60Z PC
EZ EST 60Z PC is a colloidal silica-bonded, 60% alumina castable containing zircon that can be vibration cast, pumped, or shotcreted. This castable requires an additional liquid binder (EZ ADD binder) for mixing and installation. Water is NOT added for installation.
Chemically Bonded Castables
EZ EST 95PC
EZ EST 95PC
Colloiodal Silca-bonded, Tabular Alumina Castable
Ultra Low Cement
FERMET 70 (UK)
FERMET 70 (UK)
Fermet 70 is a corundum / andalusite based ultra low cement castable with good resistance to slags found in the ferrosilicon industry.
Fermet 70 is a corundum / andalusite based ultra low cement castable with good resistance to slags found in the ferrosilicon industry.
Ultra Low Cement
FERMET 70SF (UK)
FERMET 70SF (UK)
Fermet 70SF is a self flowing corundum/mullite based ultra low cement castable with low titanium oxide and phosphate levels. It has excellant resistance to slags found in the silicon metal and ferrosilicon industries.
Pre-Cast Shapes
Fondu Panel Mix
Fondu Panel Mix
FONDU PANEL MIX is used to produce lightweight, strong, perlite based panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
Pre-Cast Shapes
Gas Panel Mix
Gas Panel Mix
GAS PANEL MIX is used to produce lightweight, strong panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
Conventional Castable
GC Sakonite
GC Sakonite
GC SAKONITE® is a “gun castable” with a 2200ºF service temperature limit. It was specially designed to give good gunning characteristics and also be a good castable. It is used in applications where conventional concrete is not refractory nor strong enough to withstand routine mechanical abuse or abrasion at elevated temperatures. It is the gunning version of standard SAKONITE® castable.
GC SAKONITE® is a “gun castable” with a 2200ºF service temperature limit. It was specially designed to give good gunning characteristics and also be a good castable. It is used in applications where conventional concrete is not refractory nor strong enough to withstand routine mechanical abuse or abrasion at elevated temperatures. It is the gunning version of standard SAKONITE® castable.
Pre-Cast Shapes
Glass Panel Mix
Glass Panel Mix
GLASS PANEL MIX is used to produce lightweight, strong, vermiculite panels. They can be manufactured to a wide range of sizes to fit special industrial needs.
Conventional Castable
Hi Strength 25
Hi Strength 25
HI-STRENGTH™ 25 is a very cost-effective, high duty refractory castable designed to resist abrasion and erosion at moderate temperatures. It has excellent thermal shock resistance and is widely used as a refractory lining and maintenance material for many different applications.
Conventional Castable
Hi Strength 26LI
Hi Strength 26LI
HI-STRENGTH™ 26-LI was developed to meet the demands for a low iron castable in the 125 Ibs/ft3 range. The lower iron content results in better resistance to reducing atmospheres. It has excellent strength throughout its temperature range and very good abrasion and erosion resistance.
Conventional Castable
Hi Strength 28LI
Hi Strength 28LI
HI-STRENGTH™ 28-LI produces a tough, monolithic structure with negligible shrinkage. It has good refractoriness with a 2800°F use limit. A casting or ramming consistency may be obtained by control of water during mixing.
Conventional Castable
HM 26 LIF
HM 26 LIF
HM 26 LIF is a Fine Grain, General Purpose Gunning Mix bonded with Low Iron Cement. HM 26 LIF can be used to repair and maintain Coke Oven Walls.
Conventional Castable
HM 28 LI
HM 28 LI
HM 28 LI is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60 % mullite content and a low iron calcium aluminate binder.
Conventional Castable
HM 28 LI CO
HM 28 LI CO
HM 28LI CO is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60% mullite content and a low iron calcium aluminate binder, designed for Coke Oven gunning
Conventional Castable
HM 28 LIF CO
HM 28 LIF CO
HM 28LIF CO is a low iron refractory gunning mix based on hard fired alumina/silica aggregate of approximately 60% mullite content and a low iron calcium aluminate binder, designed for Coke Oven gunning
Insulating Castable
KC Mix
KC Mix
KC MIX is a high performance insulating castable for a variety of kiln car applications. Its density is approximately 60 lbs/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. Use of this material at the base of kiln cars assures that under car temperatures remain well within required limits
KC MIX is a high performance insulating castable for a variety of kiln car applications. Its density is approximately 60 lbs/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. Use of this material at the base of kiln cars assures that under car temperatures remain well within required limits
Low Cement Castable
Kricon 28
Kricon 28
KRICON® 28 is a good general purpose, low iron, low cement castable for service temperatures up to 2800°F.
Low Cement Castable
Kricon 30
Kricon 30
KRICON® 30 is a low iron castable with good slag resistance up to 3000°F
Low Cement Castable
Kricon 32
Kricon 32
KRICON® 32 is designed for service temperatures up to 3200°F. It is a high alumina, low iron castable with excellent hot modulus of rupture strengths.
Wet Mortar
Ladlelock 3000 Dip
Ladlelock 3000 Dip
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 GU-TR-D3.5
Ladlelock 3000 GU-TR-D3.5
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 GU-TR-W-D3.5
Ladlelock 3000 GU-TR-W-D3.5
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 NW-TR-D2.5
Ladlelock 3000 NW-TR-D2.5
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 NW-TR-W-2.5
Ladlelock 3000 NW-TR-W-2.5
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 TF-TR-D3
Ladlelock 3000 TF-TR-D3
LADLELOCK 3000 TF is an Premium, Air-Setting, Superduty Mortar and is available in a premixed, Troweling consistency.
Wet Mortar
Ladlelock 3000 TR-D2
Ladlelock 3000 TR-D2
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 TR-D2.5
Ladlelock 3000 TR-D2.5
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 3000 TR-W-D2.5
Ladlelock 3000 TR-W-D2.5
LADLELOCK 3000 is a Premium, Air-Setting, Superduty Mortar and is available in Premixed, Troweling and Dipping consistencies
Wet Mortar
Ladlelock 50S Dip
Ladlelock 50S Dip
LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar
Ladlelock 50S Dip-W
Ladlelock 50S Dip-W
LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
LADLELOCK 50 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar
Ladlelock 70 JP-TR-D3
Ladlelock 70 JP-TR-D3
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar
Ladlelock 70 JP-TR-W-D3
Ladlelock 70 JP-TR-W-D3
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar
Ladlelock 70 TF-TR-D3
Ladlelock 70 TF-TR-D3
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar
Ladlelock 70 TR-D3.5
Ladlelock 70 TR-D3.5
LADLELOCK 70 is a Premium, Air-Setting, High Alumina Mortar and is available in Trowelling and Dipping consistencies.
Wet Mortar
Ladlelock 80 Dip
Ladlelock 80 Dip
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar
Ladlelock 80 Dip-W
Ladlelock 80 Dip-W
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar
Ladlelock 80 TR-D2
Ladlelock 80 TR-D2
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar
Ladlelock 80 TR-D3
Ladlelock 80 TR-D3
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar
Ladlelock 80 TR-W-D3
Ladlelock 80 TR-W-D3
Ladle lock 80 is a high alumina, air setting mortar, premixed. Available consistencies: dipping, trowelling (winterized versions available)
Wet Mortar
Ladlelock 85 Dip
Ladlelock 85 Dip
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
Wet Mortar
Ladlelock 85 Dip-W
Ladlelock 85 Dip-W
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
Wet Mortar
Ladlelock 85 PB-TR-D3
Ladlelock 85 PB-TR-D3
LADLELOCK 85 PB is a Premium, Phosphate-Bonded, 85% Alumina Mortar. This mortar is available in a premixed, trowelling consistency and can be used in a wide variety of mortar applications.
Wet Mortar
Ladlelock 85 PR-TR-D4
Ladlelock 85 PR-TR-D4
LADLELOCK 85 PB is a Premium, Phosphate-Bonded, 85% Alumina Mortar. This mortar is available in a premixed, trowelling consistency and can be used in a wide variety of mortar applications.
Wet Mortar
Ladlelock 85 TR-D3
Ladlelock 85 TR-D3
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
Wet Mortar
Ladlelock 85 TR-W-D3
Ladlelock 85 TR-W-D3
LADLELOCK 85 is a high alumina, premixed, air setting mortar. LADLELOCK 85 is available in standard and Winterized versions, and dipping or trowelling consistencies.
Wet Mortar
Ladlelock 90 PBP-Dip
Ladlelock 90 PBP-Dip
LADLELOCK 90 PBP is a Premium, Phosphate-Bonded, 90% Alumina Mortar and is available in a premixed, Dipping consistency.
Wet Mortar
Ladlelock 90 PB-TR-D2
Ladlelock 90 PB-TR-D2
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
Wet Mortar
Ladlelock 90 PB-TR-D3
Ladlelock 90 PB-TR-D3
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
Wet Mortar
Ladlelock 90 PB-TR-W-D2
Ladlelock 90 PB-TR-W-D2
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
Wet Mortar
Ladlelock 90 PB-TR-W-D2.5
Ladlelock 90 PB-TR-W-D2.5
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
Wet Mortar
Ladlelock 90PB-TR-D2.5
Ladlelock 90PB-TR-D2.5
LADLELOCK 90 PB is a high quality tabular alumina based, phosphate bonded mortar. LADLELOCK 90 PB is available in standard and Winterized versions.
Dry Mortar
Larcobond
Larcobond
A volume stable refractory mortar with good water retention and workability. Suitable for dipping or troweling.
Wet Mortar
Larcobond AS
Larcobond AS
LARCOBOND AS is an dry, air-setting chrome mortar that has good workability and water retention. This mortar is suitable for dipping and trowelling
Insulating Castable
LHV-124
LHV-124
LHV-124 is a lumnite, haydite, and vermiculite (LHV) mix. It is a lightweight, 60 pcf insulating castable that can be installed by casting methods.
Conventional Castable
Lo-Erode GM
Lo-Erode GM
LO-ERODE® GM is an economical, highly effective, abrasion and erosion resistant low iron gunning mix for service temperatures up to 2400°F. When properly gunned, it produces rugged monolithic linings with good volume stability.
Dry Mortar
Lo-Set
Lo-Set
LO-SET® is a 40% alumina mortar with a 3000ºF service temperature limit. When mixed with water, it produces a smooth, easy flowing mortar with good workability. It is air-setting and develops a strong bond at atmospheric temperatures. This bond strength is increased when fired at higher temperatures. Extra service life may be gained by applying a brush or spray coat of LO-SET® on any firebrick surface. Use with high duty, superduty, 50% alumina, and 60% alumina brick.
LO-SET® is a 40% alumina mortar with a 3000ºF service temperature limit. When mixed with water, it produces a smooth, easy flowing mortar with good workability. It is air-setting and develops a strong bond at atmospheric temperatures. This bond strength is increased when fired at higher temperatures. Extra service life may be gained by applying a brush or spray coat of LO-SET® on any firebrick surface. Use with high duty, superduty, 50% alumina, and 60% alumina brick.
Dry Mortar
Metaldam
Metaldam
METALDAM® is a finely ground, 50% alumina, heat-setting mortar, highly refractory to 3100ºF and recommended for use where brick and mortar come into contact with molten metal or slags. Since it is more refractory than most firebrick, it not only resists erosion, but also helps to retard brick scouring. It holds brick firmly in place, yet will release them readily during tear out of the wall or lining for repair or replacement.
METALDAM® is a finely ground, 50% alumina, heat-setting mortar, highly refractory to 3100ºF and recommended for use where brick and mortar come into contact with molten metal or slags. Since it is more refractory than most firebrick, it not only resists erosion, but also helps to retard brick scouring. It holds brick firmly in place, yet will release them readily during tear out of the wall or lining for repair or replacement.
Pre-Cast Shapes
Mighty Agg 98
Mighty Agg 98
Mighty Agg 98 is a silica free high purity alumina, low cement castable designed for maximum resistance to thermal shock and abrasion. This mix is only sold in precast shapes.
Magnesia Brick
Nuline 10-99
Nuline 10-99
Resin bonded, magnesia-carbon brick
Magnesia Brick
Nuline 13 DF
Nuline 13 DF
Resin bonded, magnesia-carbon brick
Dry Mortar
Paco Firebrick Mortar #1
Paco Firebrick Mortar #1
Dry, heat setting bonding mortar
Dry Mortar
Paco Fireclay Mortar
Paco Fireclay Mortar
Dry, heat setting bonding mortar
Dry Mortar
Paco SD Laying Mix
Paco SD Laying Mix
Conventional Castable
Pacocast 24T
Pacocast 24T
Pacocast 24T is 40% alumina, low iron castable designed to be more plastic than other conventional castables. This product can be used for patching linings and for installing by troweling or plastering rather than gunning or casting.
Conventional Castable
Pacocast 28LI
Pacocast 28LI
PACOCAST 28LI castable combines the qualities of a pyrophyllite/andalusite mineral based composition. It's low iron content makes it ideal for higher temperatures and reducing atmospheres. PACOCAST 28LI should be installed using vibration casting, It is not recommended for gunning use; for gunning see HM-28 LI.
PACOCAST 28LI castable combines the qualities of a pyrophyllite/andalusite mineral based composition. It's low iron content makes it ideal for higher temperatures and reducing atmospheres. PACOCAST 28LI should be installed using vibration casting, It is not recommended for gunning use; for gunning see HM-28 LI.
Conventional Castable
Pacocast 28LI Coarse
Pacocast 28LI Coarse
PACOCAST 28LI COARSE GRAIN offers the qualities of a Pyrophyllite/Andalusite mineral based composition in a coarse grained package. Maximum aggregate size in this product is 1/2 to 3/4 of an inch. Pacocast 28LI Coarse Grain is designed for use in applications where mechanical abuse and impacts are common.
PACOCAST 28LI COARSE GRAIN offers the qualities of a Pyrophyllite/Andalusite mineral based composition in a coarse grained package. Maximum aggregate size in this product is 1/2 to 3/4 of an inch. Pacocast 28LI Coarse Grain is designed for use in applications where mechanical abuse and impacts are common.
Alumina Brick
Patriot HF
Patriot HF
High fired, super duty, carbon monoxide resistant brick
Low Cement Castable
Permacon 95
Permacon 95
PERMACON® 95 is an ultra-low cement, 95% alumina castable, designed for severe service conditions at temperatures up to 3300°F. It offers superior resistance to spalling, cracking, impact, and abrasion; and greater resistance to chemical attack than low cement or conventional castables.
Basic Monolithics
Permanente 165 AF Castable
Permanente 165 AF Castable
PERMANENTE® 165-AF is a magnesite-based, basic castable with a unique, nonchromate bonding system and can be installed by vibration casting or ramming methods, to maximize properties.
Basic Monolithics
Permanente 165 AF Ram Mix
Permanente 165 AF Ram Mix
PERMANENTE® 165-AF RAM MIX is a fine sized high MgO material intended for leveling ladle bottoms and for backfill behind working linings in ladles, AOD degassers and other metallurgical vessels. It can be rammed or cast.
Dry Mortar
Permanente Mortar
Permanente Mortar
PERMANENTE® MORTAR is a dry, heat setting, high magnesia mortar. This magnesite mortar is designed to lay up basic brick. Ideally suited for use with magnesite or magnesia-carbon brick. This mortar is suggested for working and safety linings in both steel and non-ferrous metals applications.
PERMANENTE® MORTAR is a dry, heat setting, high magnesia mortar. This magnesite mortar is designed to lay up basic brick. Ideally suited for use with magnesite or magnesia-carbon brick. This mortar is suggested for working and safety linings in both steel and non-ferrous metals applications.
Conventional Castable
ProGun 26LI
ProGun 26LI
ProGUN® 26-LI is a conventional mix with less than 2% iron offering excellent performance in service temperatures up to 2600°F
Conventional Castable
ProGun 28LI
ProGun 28LI
ProGUN® 28-LI is a conventional mix with less than 1% iron offering excellent performance in service temperatures up to 2800°F
Conventional Castable
ProGun 30
ProGun 30
ProGUN® 30 is a very refractory, reduced cement mix targeted for general service to 3000°F
Low Cement Castable
ProGun LC 28GM
ProGun LC 28GM
ProGUN® LC 28GM is a very refractory, low cement gunning mix targeted for general service to 2800°F
Low Cement Castable
ProGun LC 30GM
ProGun LC 30GM
ProGUN® LC 30GM is a very refractory, low cement gunning mix targeted for general service to 3000°F
Low Cement Castable
ProGun LC 50G
ProGun LC 50G
ProGun LC 50G is a 3000oF low-cement gun mix. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths.
ProGun LC 50G is a 3000oF low-cement gun mix. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths.
Low Cement Castable
ProGun LC 60G
ProGun LC 60G
ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
Low Cement Castable
ProGun LC 60G (UK)
ProGun LC 60G (UK)
ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
ProGun LC 60G is a sixty percent alumina, mullite based, 3100oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give excellent gunnability, low porosity, minimum linear change, and high fired strengths. ProGun LC 60G withstands severe high temperature atmosphere reactions, and erosive corrosive environments.
Low Cement Castable
ProGun LC 70G
ProGun LC 70G
ProGun LC 70G is a 3200oF, low-cement gun mix that offers excellent resistance to alkalies. This product is designed to give minimum porosity and low linear change with maximum density and high fired strengths, and can withstand severe high temperature erosive and corrosive environments.
Conventional Castable
Purocast N
Purocast N
PUROCAST® N is a 3000°F castable that will withstand rapid heat-up. It is a low iron, high alumina material capable of withstanding reducing or hydrogen atmospheres, carbon deposition, and high sulfur fuels. It has good volume stability, excellent resistance to spalling, and low thermal conductivity.
PUROCAST® N is a 3000°F castable that will withstand rapid heat-up. It is a low iron, high alumina material capable of withstanding reducing or hydrogen atmospheres, carbon deposition, and high sulfur fuels. It has good volume stability, excellent resistance to spalling, and low thermal conductivity.
Insulating Castable
PuroLite 30
PuroLite 30
PURO-LITE® 30 is a lightweight castable with a very low iron content for service to 3000°F. It can be used in direct exposure to flame or
furnace gases, or as a backup for brick or castable. It is a low iron material with good resistance to carbon monoxide disintegration and
thermal shock.
Conventional Castable
PuroTab
PuroTab
PUROTAB® is a high purity, low iron, high alumina castable designed specifically for use at temperatures up to 3400°F. It is made with tabular alumina aggregate bonded with a high purity calcium aluminate cement. It is highly resistant to reducing atmospheres as well as high sulfur fuels and charge stocks. It has good volume stability with very good resistance to thermal shock
PUROTAB® is a high purity, low iron, high alumina castable designed specifically for use at temperatures up to 3400°F. It is made with tabular alumina aggregate bonded with a high purity calcium aluminate cement. It is highly resistant to reducing atmospheres as well as high sulfur fuels and charge stocks. It has good volume stability with very good resistance to thermal shock
Conventional Castable
Pyrocast 3000C
Pyrocast 3000C
PYROCAST 3000C is a general purpose 3000°F usage limit castable. PYROCAST 3000C may be used to form complete furnace walls, special shapes, burner blocks and other applications
Conventional Castable
Pyrocast FPM
Pyrocast FPM
PYROCAST FPM is a fine-grained, cement-bonded product that can be used for the lining in sulfur pits in oil refineries. This product has been formulated to resist attack by mild sulphur solutions. PYROCAST FPM is manufactured with a calcium silicate binder and should not be exposed to sustained temperatures above 800°F (427°C). This product can be installed by casting, gunning, or handpacking methods.
PYROCAST FPM is a fine-grained, cement-bonded product that can be used for the lining in sulfur pits in oil refineries. This product has been formulated to resist attack by mild sulphur solutions. PYROCAST FPM is manufactured with a calcium silicate binder and should not be exposed to sustained temperatures above 800°F (427°C). This product can be installed by casting, gunning, or handpacking methods.
Low Cement Castable
QuikLite 100 Rite Mix
QuikLite 100 Rite Mix
QuikLite 100 Rite Mix, Low Cement Castable
Insulating Castable
QuikLite 30
QuikLite 30
QUIKLITE 30 is a medium weight insulating castable that can be cast or gunned. QUIKLITE 30 has a 3000°F maximum service temperature and a low iron oxide content, which is suitable for most furnace atmospheres. After the initial set, this product can be heated without using the traditional ramp-and-hold heatup schedule
QUIKLITE 30 is a medium weight insulating castable that can be cast or gunned. QUIKLITE 30 has a 3000°F maximum service temperature and a low iron oxide content, which is suitable for most furnace atmospheres. After the initial set, this product can be heated without using the traditional ramp-and-hold heatup schedule
Insulating Castable
QuikLite 3-35P
QuikLite 3-35P
QUIKLITE 3-35P is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35P features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35P can be initially heated without using the traditional ramp-and-hold heatup schedule
QUIKLITE 3-35P is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35P features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35P can be initially heated without using the traditional ramp-and-hold heatup schedule
Insulating Castable
QuikLite 3-35PC
QuikLite 3-35PC
QUIKLITE 3-35PC is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35PC features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35PC can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3-35PC is a very lightweight 2000°F castable This product can be installed by casting or conventional gunning methods. QUIKLITE 3-35PC features a low installed density and low thermal conductivity. After the initial set, QUIKLITE 3-35PC can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 3A-DS
QuikLite 3A-DS
QUIKLITE 3A-DS is a dust suppressed, lightweight castable formulated for use in reducing atmospheres. This product can be installed by casting or conventional gunning methods. QUIKLITE 3A-DS features a reduced dust level and low iron oxide content. After the initial set, QUIKLITE 3A-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3A-DS is a dust suppressed, lightweight castable formulated for use in reducing atmospheres. This product can be installed by casting or conventional gunning methods. QUIKLITE 3A-DS features a reduced dust level and low iron oxide content. After the initial set, QUIKLITE 3A-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QUIKLITE 3B (UK)
QUIKLITE 3B (UK)
QUIKLITE 3B is a 50 lb/ft2 insulating material that is easily placed by troweling, gunning, or casting and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. This ease of application combined with its good insulating values makes this an ideal choice for heaters, ducts, and other related components.
QUIKLITE 3B is a 50 lb/ft2 insulating material that is easily placed by troweling, gunning, or casting and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. This ease of application combined with its good insulating values makes this an ideal choice for heaters, ducts, and other related components.
Insulating Castable
QUIKLITE 3BLI (UK)
QUIKLITE 3BLI (UK)
Quiklite 3BLI is a 1400°c low iron insulating material designed for installation by casting or gunning.It is formulated for rapid heatup without using the traditional ramp and hold heating schedule.
Insulating Castable
QuikLite 3-DS
QuikLite 3-DS
QUIKLITE 3-DS is a dust suppressed, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, a nominal 60 pcf cast density, and good strength. After the initial set, QUIKLITE 3-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 3-DS is a dust suppressed, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, a nominal 60 pcf cast density, and good strength. After the initial set, QUIKLITE 3-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 3E-DS
QuikLite 3E-DS
QUIKLITE 3E-DS is a special, dust suppressed, lightweight castable formulated for use in the petrochemical industry as a single component lining. This product can be installed by casting or conventional gunning methods. QUIKLITE 3E-DS features a reduced dust level and high strength. After the initial set, QUIKLITE 3E-DS can be initially heated without using the traditional ramp-and-hold heatup schedule. For pumping or shotcreting, QUIKLITE 3E PC is recommended.
QUIKLITE 3E-DS is a special, dust suppressed, lightweight castable formulated for use in the petrochemical industry as a single component lining. This product can be installed by casting or conventional gunning methods. QUIKLITE 3E-DS features a reduced dust level and high strength. After the initial set, QUIKLITE 3E-DS can be initially heated without using the traditional ramp-and-hold heatup schedule. For pumping or shotcreting, QUIKLITE 3E PC is recommended.
Insulating Castable
QuikLite 3PC
QuikLite 3PC
QUIKLITE 3 PC is a lightweight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 4LI
QuikLite 4LI
QUIKLITE 4LI is a high purity lightweight castable formulated for use in reducing atmospheres. This product can be installed by casting or conventional gunning methods. QUIKLITE 4LI features a low iron oxide content and good strengths . After the initial set, QUIKLITE 4LI can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 4LI is a high purity lightweight castable formulated for use in reducing atmospheres. This product can be installed by casting or conventional gunning methods. QUIKLITE 4LI features a low iron oxide content and good strengths . After the initial set, QUIKLITE 4LI can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 6
QuikLite 6
QUIKLITE 6 is a special high strength, medium weight insulating castable formulated primarily for use in the petrochemical industry. This product can be installed by conventional casting or gunning methods. After the initial set, QUIKLITE 6 can be heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 6 is a special high strength, medium weight insulating castable formulated primarily for use in the petrochemical industry. This product can be installed by conventional casting or gunning methods. After the initial set, QUIKLITE 6 can be heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 6PC
QuikLite 6PC
QUIKLITE 6 PC is a high strength, medium weight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 7-DS
QuikLite 7-DS
QUIKLITE 7-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 7-DS can be initially heated without using the traditional ramp-and-hold heatup schedule
QUIKLITE 7-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 7-DS can be initially heated without using the traditional ramp-and-hold heatup schedule
Insulating Castable
QuikLite 8-DS
QuikLite 8-DS
QUIKLITE 8-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, good strength, and a low iron content which makes this product suitable for most furnace atmospheres, including CO boilers. After the initial set, QUIKLITE 8-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 8-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, good strength, and a low iron content which makes this product suitable for most furnace atmospheres, including CO boilers. After the initial set, QUIKLITE 8-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QuikLite 8PC
QuikLite 8PC
QUIKLITE 8PC is a high strength, medium weight castable formulated to be installed by pumping or shotcreting methods. After the initial set, this unique insulating castable can be initially heated without using the traditional ramp-and-hold heatup schedule.
Insulating Castable
QUIKLITE 9 (UK)
QUIKLITE 9 (UK)
QUIKLITE 9 is a 2600°F, 90 pcf insulating castable and is formulated for a rapid heatup, without using the traditional ramp-and-hold heating schedule. QUIKLITE 9 can be installed by both casting and gunning methods.
Insulating Castable
QuikLite 9LI-DS
QuikLite 9LI-DS
QUIKLITE 9LI-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 9LI-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
QUIKLITE 9LI-DS is a dust suppressed, medium weight, insulating castable that can be installed by casting or conventional gunning methods. This castable features a reduced dust level, high strength, and a low iron content. After the initial set, QUIKLITE 9LI-DS can be initially heated without using the traditional ramp-and-hold heatup schedule.
Low Cement Castable
Quikturn 45G
Quikturn 45G
QUIKTURN 45G is an ultra-low cement, 47% alumina gun mix that is installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 45G is an ultra-low cement, 47% alumina gun mix that is installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable
QUIKTURN 50PC (UK)
QUIKTURN 50PC (UK)
QUIKTURN 50PC is a mullite-based, low cement, 60% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 50PC is a mullite-based, low cement, 60% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable
Quikturn 60G
Quikturn 60G
QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable
Quikturn 60G (UK)
Quikturn 60G (UK)
QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 60G is a mullite-based, low cement, 60% alumina low cement gun mix that can be installed by conventional gunning methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable
Quikturn 60LQY PC
Quikturn 60LQY PC
An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule.
An alkali-resistant 60% alumina castable that can be installed using vibration casting, pumping, or wet shotcreting methods. This product has been formulated to be resistant to alkali attack. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule.
Low Cement Castable
Quikturn 60PC
Quikturn 60PC
QUIKTURN 60PC is a mullite-based, low cement, 60% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 60PC is a mullite-based, low cement, 60% alumina castable that can be installed by vibration cast, pumping, and shotcreting methods. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
Low Cement Castable
Quikturn 60SF
Quikturn 60SF
QUIKTURN 60 SF is a low cement, 60% alumina that can be installed by self-flow and pumping methods. This castable was formulated for self-flowing installations. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
QUIKTURN 60 SF is a low cement, 60% alumina that can be installed by self-flow and pumping methods. This castable was formulated for self-flowing installations. After the final set, this unique castable can be heated without the traditional ramp-and-hold heatup schedule. Refer to the recommended QUIKTURN heatup schedule for the initial heatup.
RAM
RamLock 45
RamLock 45
High Strength Ramming Mix
Alumina Brick
Rescal 10 CRSR
Rescal 10 CRSR
Burned, shock resistant, alumina chrome brick
Alumina Brick
Rescal 70D
Rescal 70D
High alumina brick
Alumina Brick
Rescal 85 B
Rescal 85 B
High alumina, high strength brick
Alumina Brick
Rescal 90 XD-G
Rescal 90 XD-G
Burned, high alumina brick
Shotcrete Activator
Resco SC-1
Resco SC-1
Chemically Bonded Castables
Rescobond 3000
Rescobond 3000
RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
Chemically Bonded Castables
Rescobond 3000 (UK)
Rescobond 3000 (UK)
RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
RESCOBOND 3000 is a chemically-bonded, air-setting, single component refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 3000 with water and cast. It develops a quick set and can be heated shortly after installation.
Chemically Bonded Castables
Rescobond 3000G
Rescobond 3000G
RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
Chemically Bonded Castables
Rescobond 3000G (UK)
Rescobond 3000G (UK)
RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
RESCOBOND 3000G is a chemically-bonded, air-setting, single component gunning mix. This product can be installed by conventional gunning and handpacking methods and bonds to existing refractory. When gunning, predampening is NOT suggested for this gun mix. This product develops a quick set and can be heated shortly after installation. RESCOBOND 3000G should NOT be installed by vibration casting methods.
Chemically Bonded Castables
Rescobond 90
Rescobond 90
RESCOBOND 90 is a chemically-bonded, air-setting, single component, high purity alumina refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 90 with water and cast. It develops a quick set and can be heated shortly after installation.
RESCOBOND 90 is a chemically-bonded, air-setting, single component, high purity alumina refractory castable. This product bonds to existing refractory and can be used in a variety of different applications including patching. To use, mix RESCOBOND 90 with water and cast. It develops a quick set and can be heated shortly after installation.
Conventional Castable
Rescocast 15
Rescocast 15
RESCOCAST 15 is a hydraulic-setting, general duty castable with moderate resistance to abrasion and thermal shock. It is used in applications where high strength, moderate erosion resistance, and medium insulation values are required. Its ease of application by troweling, casting, or guniting makes it a material that can be easily installed.
RESCOCAST 15 is a hydraulic-setting, general duty castable with moderate resistance to abrasion and thermal shock. It is used in applications where high strength, moderate erosion resistance, and medium insulation values are required. Its ease of application by troweling, casting, or guniting makes it a material that can be easily installed.
Conventional Castable
Rescocast 15GM
Rescocast 15GM
RESCOCAST 15GM is a 2600°F general duty castable that can be installed by vibration casting methods. It is designed for refractory use in powerplant ash-hopper applications as well as other applications where high strength, moderate abrasion resistance, and medium insulating values are required. RESCOCAST 15GM is also an excellent gunning product that can be troweled too.
RESCOCAST 15GM is a 2600°F general duty castable that can be installed by vibration casting methods. It is designed for refractory use in powerplant ash-hopper applications as well as other applications where high strength, moderate abrasion resistance, and medium insulating values are required. RESCOCAST 15GM is also an excellent gunning product that can be troweled too.
Conventional Castable
Rescocast 17
Rescocast 17
RESCOCAST 17 is a high temperature, high purity castable providing high strength and erosion resistance throughout its entire temperature range. It also has erosion resistant properties equal to those in the extreme service group of castables. Good physical properties and ease of application have made it a universally used product throughout all industries where high temperature and high strength are requirements.
RESCOCAST 17 is a high temperature, high purity castable providing high strength and erosion resistance throughout its entire temperature range. It also has erosion resistant properties equal to those in the extreme service group of castables. Good physical properties and ease of application have made it a universally used product throughout all industries where high temperature and high strength are requirements.
Conventional Castable
Rescocast 17AC
Rescocast 17AC
RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
Conventional Castable
Rescocast 17AC (UK)
Rescocast 17AC (UK)
RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
RESCOCAST 17AC is a high temperature, high purity alumina conventional castable with only trace amounts of silica and iron oxide. The high purity of this castable makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using vibration casting methods.
Conventional Castable
Rescocast 17AC Coarse
Rescocast 17AC Coarse
RESCOCAST 17AC COARSE is a high purity, low iron, low silica hydraulic setting castable that contains a coarse aggregate. Low iron and low silica contents of less than 0.1 to 0.2 percent make RESCOCAST 17AC COARSE an ideal choice for reducing atmospheres such as hydrogen and/or carbon monoxide.
RESCOCAST 17AC COARSE is a high purity, low iron, low silica hydraulic setting castable that contains a coarse aggregate. Low iron and low silica contents of less than 0.1 to 0.2 percent make RESCOCAST 17AC COARSE an ideal choice for reducing atmospheres such as hydrogen and/or carbon monoxide.
Conventional Castable
Rescocast 17AG
Rescocast 17AG
RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
Conventional Castable
Rescocast 17AG (UK)
Rescocast 17AG (UK)
RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
RESCOCAST 17AG is a high temperature, high purity alumina conventional gunning mix with only trace amounts of silica and iron oxide. The high purity of this gunning mix makes it an ideal choice for reducing atmospheres containing hydrogen and/or carbon monoxide. This product should be installed using conventional gunning methods. Data shown below are average results of tests following the guidelines set forth in ASTM C-903 "Preparing Refractory Concrete Specimens by Cold Gunning".
Conventional Castable
RESCOCAST 17E (UK)
RESCOCAST 17E (UK)
Rescocast 17E has been used for many years as an erosion resistant lining material. It's low iron content makes it a good choice for units operating with high co contents, such as blast furnace take-offs and flue gas lines. Rescocast 17E is used in applications where it is not practical to install the material by vibration casting or gunning. Typically it would be used handpacking installations such as field joints or applications using hex-steel type anchorage systems.
Rescocast 17E has been used for many years as an erosion resistant lining material. It's low iron content makes it a good choice for units operating with high co contents, such as blast furnace take-offs and flue gas lines. Rescocast 17E is used in applications where it is not practical to install the material by vibration casting or gunning. Typically it would be used handpacking installations such as field joints or applications using hex-steel type anchorage systems.
Conventional Castable
RESCOCAST 17G (UK)
RESCOCAST 17G (UK)
RESCOCAST 17G is a high temperature, high purity castable providing high strength and erosion resistance throughout its entire temperature range. RESCOCAST 17G has been formulated for gunite application with minimum rebound losses and uniform flow to the nozzle. Data shown are average results of tests following the guidelines set forth in ASTM C-903-70, “Preparing Refractory Concrete Specimens by Cold Gunning”
RESCOCAST 17G is a high temperature, high purity castable providing high strength and erosion resistance throughout its entire temperature range. RESCOCAST 17G has been formulated for gunite application with minimum rebound losses and uniform flow to the nozzle. Data shown are average results of tests following the guidelines set forth in ASTM C-903-70, “Preparing Refractory Concrete Specimens by Cold Gunning”
Insulating Castable
Rescocast 3
Rescocast 3
RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
Insulating Castable
Rescocast 3 (UK)
Rescocast 3 (UK)
RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
RESCOCAST 3 is a high performance insulating castable designed for a variety of applications. Its density is approximately 60 lb/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3 can be installed by either gunning or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3 PC is recommended.
Insulating Castable
Rescocast 3-20R
Rescocast 3-20R
RESCOCAST 3-20R is a lightweight insulating material designed to replace insulating block. Its low density results in very low “K” factors for super insulation. It can be used as a back up material in bi-wall linings or as a single component lining where the temperatures are not to exceed 2000°F.
RESCOCAST 3-20R is a lightweight insulating material designed to replace insulating block. Its low density results in very low “K” factors for super insulation. It can be used as a back up material in bi-wall linings or as a single component lining where the temperatures are not to exceed 2000°F.
Insulating Castable
Rescocast 3-35
Rescocast 3-35
RESCOCAST 3-35 is an insulating castable with an operating temperature up to 2000°F, with a good strength to density ratio. It has been used as an insulating material in bi-wall linings and also as a single component lining where erosive conditions are not too severe. Unlike loose fill or insulating block, RESCOCAST 3-35 will not settle or disintegrate under adverse conditions.
RESCOCAST 3-35 is an insulating castable with an operating temperature up to 2000°F, with a good strength to density ratio. It has been used as an insulating material in bi-wall linings and also as a single component lining where erosive conditions are not too severe. Unlike loose fill or insulating block, RESCOCAST 3-35 will not settle or disintegrate under adverse conditions.
Insulating Castable
Rescocast 3-35P
Rescocast 3-35P
RESCOCAST 3-35P is an insulating castable with an operating temperature up to 2000°F, with a good strength to density ratio. It has been used as an insulating material in bi-wall linings and also as a single component lining where erosive conditions are not too severe. Unlike loose fill or insulating block, RESCOCAST 3-35P will not settle or disintegrate under adverse conditions.
RESCOCAST 3-35P is an insulating castable with an operating temperature up to 2000°F, with a good strength to density ratio. It has been used as an insulating material in bi-wall linings and also as a single component lining where erosive conditions are not too severe. Unlike loose fill or insulating block, RESCOCAST 3-35P will not settle or disintegrate under adverse conditions.
Insulating Castable
Rescocast 3-35PC
Rescocast 3-35PC
RESCOCAST 3-35PC is an insulating castable with an operating temperature up to 2000°F, and a good strength to density ratio. It can be used as an insulating material in bi-wall linings and also as a single component lining, where erosive conditions are not too severe. Unlike loose fill or soft insulating block, RESCOCAST 3-35PC will not settle or disintegrate under adverse conditions
RESCOCAST 3-35PC is an insulating castable with an operating temperature up to 2000°F, and a good strength to density ratio. It can be used as an insulating material in bi-wall linings and also as a single component lining, where erosive conditions are not too severe. Unlike loose fill or soft insulating block, RESCOCAST 3-35PC will not settle or disintegrate under adverse conditions
Insulating Castable
Rescocast 3A
Rescocast 3A
RESCOCAST 3A is a lightweight, low iron, insulating castable which has a service limit temperature of 2500°F. It is used primarily where reducing atmospheres may be present. RESCOCAST 3A can be installed by either gunning or casting methods.
Insulating Castable
Rescocast 3A (UK)
Rescocast 3A (UK)
RESCOCAST 3A is a lightweight, low iron, insulating castable which has a service limit temperature of 2500°F. It is used primarily where reducing atmospheres may be present. RESCOCAST 3A can be installed by either gunning or casting methods.
Pre-Cast Shapes
Rescocast 3A Panel Mix
Rescocast 3A Panel Mix
RESCOCAST 3A is a lightweight, low iron, insulating panel mix which has a service limit temperature of 2500oF. It is used primarily where reducing atmospheres may be present.
Insulating Castable
RESCOCAST 3APC
RESCOCAST 3APC
RESCOCAST 3APC is a lightweight, low iron, insulating castable which has a service limit temperature of 2500oF. It is used primarily where reducing atmospheres may be present. RESCOCAST 3APC can be applied by either casting, pump casting or wet shotcrete methods.
Insulating Castable
RESCOCAST 3B
RESCOCAST 3B
RESCOCAST 3B insulating castable is a 50 pcf density castable that can be installed by troweling, casting or conventional gunning methods
Insulating Castable
Rescocast 3E
Rescocast 3E
RESCOCAST 3E is a high strength, special lightweight heat insulating castable designed primarily for use in the petrochemical industry for single component linings in FCC vessels, etc. The product can be applied by gunite or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3E PC is recommended.
RESCOCAST 3E is a high strength, special lightweight heat insulating castable designed primarily for use in the petrochemical industry for single component linings in FCC vessels, etc. The product can be applied by gunite or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3E PC is recommended.
Insulating Castable
Rescocast 3E (UK)
Rescocast 3E (UK)
RESCOCAST 3E is a high strength, special lightweight heat insulating castable designed primarily for use in the petrochemical industry for single component linings in FCC vessels, etc. The product can be applied by gunite or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3E PC is recommended.
RESCOCAST 3E is a high strength, special lightweight heat insulating castable designed primarily for use in the petrochemical industry for single component linings in FCC vessels, etc. The product can be applied by gunite or casting methods. For pumpcasting or shotcreting applications, RESCOCAST 3E PC is recommended.
Insulating Castable
Rescocast 3PC
Rescocast 3PC
RESCOCAST 3PC is a high performance insulating castable designed for a variety of applications. Its pumpcast density is approximately 56 lbs/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3PC can be installed by casting, pumpcasting, or shotcreting methods.
RESCOCAST 3PC is a high performance insulating castable designed for a variety of applications. Its pumpcast density is approximately 56 lbs/ft3 and offers superior strength characteristics, as well as a high strength-to-insulation ratio. This material can be used as an original lining material or as a replacement for refractory ceramic fiber. RESCOCAST 3PC can be installed by casting, pumpcasting, or shotcreting methods.
Insulating Castable
Rescocast 4LI
Rescocast 4LI
RESCOCAST 4LI, a low iron, high purity, lightweight insulating castable, is especially formulated for use in controlled atmospheres such as methane, hydrogen, and carbon monoxide. RESCOCAST 4LI has been used in many heater applications, such as pre-fabricated panels, resulting in minimum downtime. RESCOCAST 4LI can be installed by either gunning or casting methods.
RESCOCAST 4LI, a low iron, high purity, lightweight insulating castable, is especially formulated for use in controlled atmospheres such as methane, hydrogen, and carbon monoxide. RESCOCAST 4LI has been used in many heater applications, such as pre-fabricated panels, resulting in minimum downtime. RESCOCAST 4LI can be installed by either gunning or casting methods.
Insulating Castable
Rescocast 6
Rescocast 6
RESCOCAST 6 is a high strength, special medium-weight heat insulating castable designed primarily for use in the petrochemical industry where higher strength and temperature requirements are needed. RESCOCAST 6 can be installed by both gunning and casting methods. For pumpcasting or shotcreting applications, RESCOCAST 6PC is recommended.
RESCOCAST 6 is a high strength, special medium-weight heat insulating castable designed primarily for use in the petrochemical industry where higher strength and temperature requirements are needed. RESCOCAST 6 can be installed by both gunning and casting methods. For pumpcasting or shotcreting applications, RESCOCAST 6PC is recommended.
Insulating Castable
Rescocast 6 (UK)
Rescocast 6 (UK)
RESCOCAST 6 is a high strength, special medium-weight heat insulating castable designed primarily for use in the petrochemical industry where higher strength and temperature requirements are needed. RESCOCAST 6 can be installed by both gunning and casting methods. For pumpcasting or shotcreting applications, RESCOCAST 6PC is recommended.
RESCOCAST 6 is a high strength, special medium-weight heat insulating castable designed primarily for use in the petrochemical industry where higher strength and temperature requirements are needed. RESCOCAST 6 can be installed by both gunning and casting methods. For pumpcasting or shotcreting applications, RESCOCAST 6PC is recommended.
Insulating Castable
Rescocast 6PC
Rescocast 6PC
RESCOCAST 6PC is a high strength, medium weight insulating castable designed primarily for pumpcasting and shotcreting installation methods. RESCOCAST 6PC can also be installed using standard casting methods. It has been applied by pumpcasting on both regenerator and reactor vessel walls, as well as in fired heaters. Pumpcasting and shotcreting methods produce a uniform, lamination free lining when compared to gunned linings.
RESCOCAST 6PC is a high strength, medium weight insulating castable designed primarily for pumpcasting and shotcreting installation methods. RESCOCAST 6PC can also be installed using standard casting methods. It has been applied by pumpcasting on both regenerator and reactor vessel walls, as well as in fired heaters. Pumpcasting and shotcreting methods produce a uniform, lamination free lining when compared to gunned linings.
Insulating Castable
Rescocast 7
Rescocast 7
RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
Insulating Castable
Rescocast 7 (UK)
Rescocast 7 (UK)
RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
RESCOCAST 7 is the original "one shot" lining material for use in FCC regenerator and reactor vessel walls. Good strength combined with better insulating qualities and an economical cost make RESCOCAST 7 an ideal choice for many applications. Although primarily used as a gunning material, it can also be cast or troweled into place.
Insulating Castable
Rescocast 8
Rescocast 8
RESCOCAST 8 is a medium weight, insulating castable with a service limit temperature of 2800°F. A low iron content makes it suitable for most furnace atmospheres, including CO Boilers. RESCOCAST 8 can be installed by either casting or gunning.
Insulating Castable
Rescocast 8 (UK)
Rescocast 8 (UK)
RESCOCAST 8 is a medium weight, insulating castable with a service limit temperature of 2800°F. A low iron content makes it suitable for most furnace atmospheres, including CO Boilers. RESCOCAST 8 can be installed by either casting or gunning.
Insulating Castable
Rescocast 8PC
Rescocast 8PC
RESCOCAST 8 PC is a medium weight insulating castable that can be vibration cast, pumped, or shotcreted. RESCOCAST 8 PC has a 2800°F maximum service temperature and a low iron oxide content, which is suitable for most furnace atmospheres.
Insulating Castable
Rescocast 9
Rescocast 9
RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
Insulating Castable
Rescocast 9 (UK)
Rescocast 9 (UK)
RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
RESCOCAST 9 combines the qualities of an insulating and a general duty castable. High strength and good protection against heat loss have made this product an ideal choice for the gunning of FCC regenerator and reactor walls. RESCOCAST 9 has been used throughout the world for this and other critical applications. RESCOCAST 9 can be installed by either casting or gunning. For a pumpcasting or shotcreting applications, Rescocast 9LIPC is recommended.
Insulating Castable
RescoLite 23-50LI
RescoLite 23-50LI
RESCOLITE 23-50 LI is a low iron, lightweight castable with a nominal 50 pcf density that can be installed by casting or conventional gunning methods. This low iron lightweight castable is suitable for reducing and hydrogen atmospheres.
Plastic
Rescoram 10CR
Rescoram 10CR
RESCORAM 10 CR is a high alumina, phosphate-bonded plastic with 10% chromic oxide that is used throughout the metals producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 10 CR is a high alumina, phosphate-bonded plastic with 10% chromic oxide that is used throughout the metals producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic
Rescoram 20CR
Rescoram 20CR
RESCORAM 20CR is a Phosphate-Bonded Alumina-Chrome Plastic that contains 20% chromic oxide, for increased slag and corrosion resistance.
Plastic
Rescoram 60
Rescoram 60
RESCORAM 60 is a high alumina, phosphate-bonded plastic that offers excellent resistance to alkali attack. Phosphate bonding allows RESCORAM 60 to develop high strength at lower temperatures.
Plastic
Rescoram 70 Blue
Rescoram 70 Blue
RESCORAM 70 BLUE is a mullite, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics. This product is designed to resist alkali attack.
RESCORAM 70 BLUE is a mullite, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics. This product is designed to resist alkali attack.
Plastic
Rescoram 70SC
Rescoram 70SC
RESCORAM 70 SC is a 70% silicon carbide, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 70 SC is a 70% silicon carbide, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic
Rescoram 7CR
Rescoram 7CR
RESCORAM 7 CR is a high alumina, phosphate-bonded plastic with 7% chromic oxide that is used throughout the metals producing industries. RESCORAM 7 CR has a chemical bond that develops a high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 7 CR is a high alumina, phosphate-bonded plastic with 7% chromic oxide that is used throughout the metals producing industries. RESCORAM 7 CR has a chemical bond that develops a high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic
Rescoram 85
Rescoram 85
RESCORAM 85 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 85 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic
Rescoram 85S
Rescoram 85S
Phosphate bonded alumina plastic
Plastic
Rescoram 90
Rescoram 90
RESCORAM 90 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
RESCORAM 90 is a high alumina, phosphate-bonded plastic material that is used throughout the metals, power, cement, and lime producing industries. Its chemical bond develops high strength at lower temperatures. This property makes it ideal for application where there is insufficient heat to develop the ceramic bond required in heat-setting plastics.
Plastic
Rescoram A-45HC
Rescoram A-45HC
Rescoram A-45HC is a super duty, air-setting, plastic refractory that is designed primarily for high temperature boiler service. This product exceeds ASTM standard for PCE 32-1/2.
Plastic
Rescoram A-60
Rescoram A-60
RESCORAM A-60 is a high alumina, air-setting, 3100°F service temperature plastic refractory that is used throughout the metals, power, cement, and lime producing industries where higher temperature requirements demand a more refractory material. It is manufactured using Pyrophyllite-Andalusite-Alumina materials which give the product unique long term hot load resistance.
RESCORAM A-60 is a high alumina, air-setting, 3100°F service temperature plastic refractory that is used throughout the metals, power, cement, and lime producing industries where higher temperature requirements demand a more refractory material. It is manufactured using Pyrophyllite-Andalusite-Alumina materials which give the product unique long term hot load resistance.
Plastic
Rescoram A-80
Rescoram A-80
RESCORAM A-80 is a high alumina, air-setting, 3300°F service temperature plastic refractory that is used throughout the metals, power, cement and lime producing industries where higher temperature requirements demand a higher PCE or more refractory material.
Plastic
Rescoram A-90
Rescoram A-90
An air setting 90% alumina plastic. This product should be installed by pneumatic ramming.
Wet Mortar
Rescoset 10CR Dip
Rescoset 10CR Dip
Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Wet Mortar
Rescoset 10CR TR-D3
Rescoset 10CR TR-D3
Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Rescoset 10CR is a wet high alumina-chrome oxide bonding mortar with a chemical bonding system. With the unique bonding system, high strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 10CR is primarily used to lay up alumina-chrome brick oxide and is available in a troweling consistency. It is recommended in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Wet Mortar
Rescoset 3000 TR-D3.5
Rescoset 3000 TR-D3.5
RESCOSET 3000 is a super duty, air-setting bonding mortar with a maximum recommended service temperature of 3000°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Wet Mortar
Rescoset 50M TR-D3
Rescoset 50M TR-D3
RESCOSET 50M is a high alumina class, mullite based, air-setting bonding mortar with a maximum recommended service temperature of 3000°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Wet Mortar
Rescoset 80P TR-D3
Rescoset 80P TR-D3
Rescoset 80P is a wet high alumina bonding mortar with improved shelf life. With the unique chemical bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 80P is primarily used to lay up high alumina brick and is available in troweling and dipping consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Rescoset 80P is a wet high alumina bonding mortar with improved shelf life. With the unique chemical bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 80P is primarily used to lay up high alumina brick and is available in troweling and dipping consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance.
Wet Mortar
Rescoset 85AS TR
Rescoset 85AS TR
Wet, air-setting, 85% alumina bonding mortar with a low silica content
Wet Mortar
Rescoset 90P TR-D3
Rescoset 90P TR-D3
Rescoset 90P is a wet high alumina bonding mortar with a chemical bonding system. With the unique bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 90P is primarily used to lay up high alumina brick and is available in troweling consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance
Rescoset 90P is a wet high alumina bonding mortar with a chemical bonding system. With the unique bonding system, high bonding strength is developed at lower temperatures (300-600°F) and continues until a ceramic bonding occurs. Rescoset 90P is primarily used to lay up high alumina brick and is available in troweling consistency. It is used in areas where severe service conditions require increased refractoriness and corrosion/erosion resistance
Wet Mortar
Rescoset Chrome Mortar
Rescoset Chrome Mortar
Chrome based Mortar
Wet Mortar
Rescoset MD TR
Rescoset MD TR
RESCOSET MD is an air-setting bonding mortar with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Wet Mortar
RESCOSET MD-TR-D4
RESCOSET MD-TR-D4
RESCOSET MD is an air-setting bonding mortar with a maximum recommended service temperature of 2800°F. It is shipped as a wet, ready to use mortar and will stay in suspension over long periods of time.
Low Cement Castable
R-Max 85Z
R-Max 85Z
R-MAX 85Z is a Abrasion-Resistant 85% Alumina Castable that contains Zircon for severe wear applications in the cement industry. This castable features very high abrasion resistance with good flow under vibration. This castable should be installed by vibration casting only.
Low Cement Castable
R-Max C
R-Max C
R-MAX C is a Abrasion-Resistant, Low Cement 70% Alumina Castable. This castable should be installed by vibration casting only; specifically form vibration.
Low Cement Castable
R-Max C (ESC)
R-Max C (ESC)
R-MAX C is a Abrasion-Resistant, Low Cement 70% Alumina Castable. This castable should be installed by vibration casting only; specifically form vibration.
Low Cement Castable
R-Max G
R-Max G
R-MAX G is a 3200°F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. R-Max G should be installed using conventional gunning methods.
Low Cement Castable
R-Max G (ESC)
R-Max G (ESC)
R-MAX G is a 3200 °F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. RMax G should be installed using conventional gunning methods. The data shown are average test results following the guidelines set forth in ASTM C-903; “Preparing Refractory Concrete Specimens by Cold Gunning”.
R-MAX G is a 3200 °F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. RMax G should be installed using conventional gunning methods. The data shown are average test results following the guidelines set forth in ASTM C-903; “Preparing Refractory Concrete Specimens by Cold Gunning”.
Low Cement Castable
R-Max G (UK)
R-Max G (UK)
R-MAX G is a 3200°F high performance gunning mix designed to provide maximum abrasion resistance and excellent strengths throughout all operating temperatures. R-Max G should be installed using conventional gunning methods.
Low Cement Castable
R-Max G QT
R-Max G QT
R-MAX G QT is a high performance gunning mix designed to provide high abrasion resistance and excellent strengths. R-Max G QT should be installed using conventional gunning methods. After the final set, this unique gun mix can be heated without the traditional controlled heating schedule. Ideal applications for this product include areas of severe abrasion, where refractory heatup is difficult to control or a shorter heatup schedule is desired.
R-MAX G QT is a high performance gunning mix designed to provide high abrasion resistance and excellent strengths. R-Max G QT should be installed using conventional gunning methods. After the final set, this unique gun mix can be heated without the traditional controlled heating schedule. Ideal applications for this product include areas of severe abrasion, where refractory heatup is difficult to control or a shorter heatup schedule is desired.
Low Cement Castable
R-Max PC
R-Max PC
R-MAX PC is a Pumpable, Abrasion-Resistant, 70% Alumina Castable. This castable can be installed by vibration casting, pumping, or shotcreting methods
Low Cement Castable
R-Max PC QT
R-Max PC QT
R-MAX PC QT is a Pumpable, Abrasion-Resistant, 80% Alumina Castable. This castable can be installed by vibration casting and pumping methods. Ideal applications for this castable are severe abrasion areas where refractory heatup is difficult to control.
Low Cement Castable
R-Max PC QT (UK)
R-Max PC QT (UK)
R-MAX PC QT is a Pumpable, Abrasion-Resistant, 80% Alumina Castable. This castable can be installed by vibration casting and pumping methods. Ideal applications for this castable are severe abrasion areas where refractory heatup is difficult to control.
Low Cement Castable
R-Max SF
R-Max SF
A self leveling, 92% alumina castable with maximum erosion resistance, that can installed using the products’s self leveling characteristic or pumpcasting methods. This product should be used in areas subjected to severe abrasion. It is suggested that vibration should not be used during installation since it is a self leveling product.
A self leveling, 92% alumina castable with maximum erosion resistance, that can installed using the products’s self leveling characteristic or pumpcasting methods. This product should be used in areas subjected to severe abrasion. It is suggested that vibration should not be used during installation since it is a self leveling product.
Conventional Castable
Sakonite
Sakonite
SAKONITE® is a very economical refractory concrete. Although its maximum service temperature is 2200°F, it is designed primarily for service between 70°F and 1000°F. It is widely used for cast floors exposed to molten metals or hot ingots. It can be cast or pumped and finished like ordinary concrete. It may also be rammed or cast-vibrated for increased density and strength with minimum shrinkage. SAKONITE® is also available as GC SAKONITE® gun mix.
SAKONITE® is a very economical refractory concrete. Although its maximum service temperature is 2200°F, it is designed primarily for service between 70°F and 1000°F. It is widely used for cast floors exposed to molten metals or hot ingots. It can be cast or pumped and finished like ordinary concrete. It may also be rammed or cast-vibrated for increased density and strength with minimum shrinkage. SAKONITE® is also available as GC SAKONITE® gun mix.
Alumina Brick
Seneca 60 P
Seneca 60 P
Burned, high alumina brick
Wet Mortar
Super Adamant Dip
Super Adamant Dip
SUPER ADAMANT is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. SUPER ADAMANT has a maximum recommended service temperature of 3000oF. The product has excellent slag resistance, and its low iron content makes it ideal for reducing atmospheres. It has the same smooth working characteristics built into all RESCO mortars and has been used successfully in blast furnaces, hot metal mixers, electric furnace roofs, soaking pits, stopper rods, ladles, and other applications where severe conditions exist.
SUPER ADAMANT is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. SUPER ADAMANT has a maximum recommended service temperature of 3000oF. The product has excellent slag resistance, and its low iron content makes it ideal for reducing atmospheres. It has the same smooth working characteristics built into all RESCO mortars and has been used successfully in blast furnaces, hot metal mixers, electric furnace roofs, soaking pits, stopper rods, ladles, and other applications where severe conditions exist.
Wet Mortar
Super Adamant TR
Super Adamant TR
SUPER ADAMANT is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. SUPER ADAMANT has a maximum recommended service temperature of 3000oF. The product has excellent slag resistance, and its low iron content makes it ideal for reducing atmospheres. It has the same smooth working characteristics built into all RESCO mortars and has been used successfully in blast furnaces, hot metal mixers, electric furnace roofs, soaking pits, stopper rods, ladles, and other applications where severe conditions exist.
SUPER ADAMANT is a wet ready-mixed high alumina based bonding mortar available in either trowel or dipping consistencies. SUPER ADAMANT has a maximum recommended service temperature of 3000oF. The product has excellent slag resistance, and its low iron content makes it ideal for reducing atmospheres. It has the same smooth working characteristics built into all RESCO mortars and has been used successfully in blast furnaces, hot metal mixers, electric furnace roofs, soaking pits, stopper rods, ladles, and other applications where severe conditions exist.
Wet Mortar
Trowleze TR
Trowleze TR
TROWLEZE® Is a 40% alumina, versatile bonding mortar with exceptional troweling and buttering workability. It adheres to the trowel so it can be picked up and transferred to the brick without difficulty. It provides a strong, air-set bond and an even stronger ceramic bond upon firing. It has excellent volume stability, minimum shrinkage, high refractoriness to 3000ºF, uniform workability, good water retention, and thorough coverage for economical use. Use with high duty, superduty, 50% alumina, and 60% alumina brick. It is the recommended mortar of choice for installing insulating firebrick.
TROWLEZE® Is a 40% alumina, versatile bonding mortar with exceptional troweling and buttering workability. It adheres to the trowel so it can be picked up and transferred to the brick without difficulty. It provides a strong, air-set bond and an even stronger ceramic bond upon firing. It has excellent volume stability, minimum shrinkage, high refractoriness to 3000ºF, uniform workability, good water retention, and thorough coverage for economical use. Use with high duty, superduty, 50% alumina, and 60% alumina brick. It is the recommended mortar of choice for installing insulating firebrick.
Conventional Castable
Unicrete 28LI
Unicrete 28LI
UNICRETE 28 LI is a low iron casting mix based on high fired alumina/silica aggregate of approximately 60% mullite content, bonded with low iron calcium aluminate cement. UNICRETE 28 LI can be used in coke oven, blast furnace, and other applications where reducing conditions occur.
Low Cement Castable
Unicrete 50 Flowz
Unicrete 50 Flowz
UNICRETE 50 FLOWZ is a self-flow, shotcretable, low cement castable. The properties of low cement castables are sensitive to the amount of mixing water used during casting. The best physical properties are achieved when mixing water is kept to a minimum, the material is mixed thoroughly and as much vibration as possible is used when casting.
UNICRETE 50 FLOWZ is a self-flow, shotcretable, low cement castable. The properties of low cement castables are sensitive to the amount of mixing water used during casting. The best physical properties are achieved when mixing water is kept to a minimum, the material is mixed thoroughly and as much vibration as possible is used when casting.
Low Cement Castable
Unicrete 60 Flowz
Unicrete 60 Flowz
UNICRETE 60 FLOWZ is a self-flow, shotcretable, low cement castable. The properties of low cement castables are sensitive to the amount of mixing water used during casting. The best physical properties are achieved when mixing water is kept to a minimum, the material is mixed thoroughly and as much vibration as possible is used when casting.
UNICRETE 60 FLOWZ is a self-flow, shotcretable, low cement castable. The properties of low cement castables are sensitive to the amount of mixing water used during casting. The best physical properties are achieved when mixing water is kept to a minimum, the material is mixed thoroughly and as much vibration as possible is used when casting.
Pre-Cast Shapes
Uniform 65LC
Uniform 65LC
UNIFORM 65 LC is a precast shape made with a high strength, low moisture castable based on hard fired alumina/silica aggregate. UNIFORM 65 LC is designed for maximum resistance to abrasion and erosion.
Pre-Cast Shapes
Uniform 70 UCXC
Uniform 70 UCXC
UNIFORM 70 UCXC is a coarse grain-containing, ultralow cement, 70% alumina precast shape. This precast mix features excellent dimensional stability, strength, and corrosion resistance and is available with stainless steel fibers for additional strength and spall resistance.
Pre-Cast Shapes
Uniform 85LCXC
Uniform 85LCXC
UNIFORM 85 LCXC is a precast shape made with an Coarse Grain-containing 85% Alumina, Low Cement Castable. For added strength and spalling resistance, UNIFORM 85 LCXC is available with stainless steel fiber additions.
Pre-Cast Shapes
Uniform 90ARS
Uniform 90ARS
Uniform 90 ARS is a precast shape made with a tabular alumina / spinel, low moisture castable. The addition of spinel significantly improves this castables hot strength and resistance to slag attack.
Pre-Cast Shapes
Uniform R Max 4%HCA
Uniform R Max 4%HCA
Low Cement Castable
Vibrocast 2800
Vibrocast 2800
VIBROCAST 2800 is an economical 2800°F low cement castable designed to yield high fired strengths at maximum density. This product should be installed by vibration casting methods only.
Low Cement Castable
Vibrocast 3000
Vibrocast 3000
VIBROCAST 3000 is an economical, Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable
Vibrocast 50
Vibrocast 50
VIBROCAST 50 is a Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable
Vibrocast 50 (UK)
Vibrocast 50 (UK)
VIBROCAST 50 is a Low Cement, 45% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable
Vibrocast 50PC
Vibrocast 50PC
VIBROCAST 50PC is a Pumpable, Low Cement, 45% Alumina castable that can be installed by vibration casting, pumping, and shotcreting methods. It offers excellent resistance to alkalis and requires substantially less vibration than standard low cement castables.
Low Cement Castable
Vibrocast 60
Vibrocast 60
VIBROCAST 60 is a Mullite-Based, Low Cement, 60% Alumina castable that can be installed by vibration cast methods only.
Low Cement Castable
Vibrocast 60PC
Vibrocast 60PC
VIBROCAST 60PC is a Pumpable, Low Cement, 60% Alumina castable based on a mullite aggregate, that can be installed by vibration cast, pumping, and shotcreting methods.
Low Cement Castable
Vibrocast 60Z PC
Vibrocast 60Z PC
A 60% alumina, low cement castable containing zircon. This product can be installed using vibration casting, pumping, and shotcrete installation methods.
Low Cement Castable
Vibrocast 70M
Vibrocast 70M
VIBROCAST 70M is an economical, low cement 70% alumina with good cast density and high strengths formulated to withstand high temperatures. This product should be installed by vibration casting methods only.
Low Cement Castable
Vibrocast 75
Vibrocast 75
VIBROCAST 75 is an economical, Low Cement, 75% Alumina castable that can be installed by vibration cast methods only.
Get a Quote